Printhead 950 951 For HP Officejet Pro 8100 8600 8610 8620 8630 8640 251dw 276dw

Save 17%
vipih.comSKU: W002-D015

$139.99 $168


Before you buy this product, you need to pay attention to:

NOTE: The printer must be disconnected from the power source before the print head is installed, otherwise it has the risk of causing the print head circuit board to burn out.
1. When the print head is shipped, a protective liquid will be applied to the print head. Before using it for the first time, wipe the print head before installing it.Just wipe the copper sheet gently, wipe it clean with soft paper, don't wipe it with cleaning fluid or eraser.
2. During the regeneration process of the print head, the ink will be cleaned and the protection liquid will be injected. If there is no protective liquid, the print head cannot print because the pipeline channel is dry.If the print head can be detected, but the colors are uneven or blurred, you can continue printing with ink. Print a few more sheets of paper and wait for the excess protection fluid to run out, then you can print normally
3. If the printing effect is not clear, press the machine cleaning button to clean (the print head must be cleaned only when the ink cartridge is sufficient, or it will burn out easily).
4. You don't need to clean the print head with cleaning fluid, you can clean the print head directly on the machine. If you clean the print head with the cleaning fluid(or water) and do not drop the protective fluid, the print head will be completely blocked, and it will be useless.

Printhead 950 951 For HP Officejet Pro 8100 8600 8610 8620 8630 8640 251dw 276dw

Before you install this product, you need to pay attention to:
1.After receiving the print head, if you use a needle tube to inject water to check the nozzle or see if it is blocked, this is a very redundant and dangerous behavior.If the printing effect is not clear, press the machine cleaning button (the pFirst of all, once the print head enters the water, if the water is not dry, it is powered on. The main board will be burned out, and the print head will be burnt out. Secondly, the print heads sold in our shop have been strictly tested and filled with protective liquid.If you use a needle to inject water into the print head, it will not only wash away the protective liquid in the head, but also easily cause air blockage in the print head, resulting in no ink.
2.Be careful when installing the print head, be sure to cut off the power first, and install it in place.
3.When connecting the plug cable, do not have ink on it, and make sure that it is in good contact with the socket.
4.The steel shaft should also be clean and smooth. You can use a paper towel to stick some lubricating oil to wipe it. Do not directly add oil to the shaft. The excess oil will flow to the print head and cause damage.
5.After the machinery and circuit are all correct, check the water circuit. Firstly, check whether the ink volume in the ink cartridge is sufficient; secondly, check whether the small cleaning blade and the ink suction pump are dirty.
6.There will be air in the newly installed print head, so it will not print normally immediately. The printer can only produce perfect results after the air in the head is completely discharged.You can use the machine's own cleaning function for intermittent cleaning(Clean 2 times each time, and then 2 times after 30 minutes) Repeated over-cleaning will cause ink accumulation in the cleaning pump, which will not only cause color mixing, ink leakage, and waste ink.Finally, you can print more pictures to let the print head exhaust air during work.

Reufrbished 950 951 Printhead for Hp officejet pro 8100 8600 CM751 950 951Printhead for Hp 8100 8600 8610 8620 8630 8640 251dw 276dw

1.Excellent performance and high quality.
2.Made of high-quality material, durable, firm and stable for us to use.
3.This is a cleaned, thoroughly tested and sealed Printhead.
4.Good stability, long lifespan.
5.Full color function.

Fits Following Model(s):
Refurbished 950 951 Printhead
For Hp officejet pro 8100
For Hp officejet pro 8600
For Hp officejet pro CM751
For Hp officejet pro CM752
For Hp officejet pro N811A
For Hp officejet pro 251dw
For Hp officejet pro 276dw
For Hp officejet pro 8610
For Hp officejet pro 8620
For Hp officejet pro 8630
For Hp officejet pro 8640

Pacakge Included:
1 x print head

Printhead 950 951 For HP Officejet Pro 8100 8600 8610 8620 8630 8640 251dw 276dw

1.In print entered please turn off the power of the printer, or it will cause the mainboard chip burned.
After loading the print head, please don't install ribbon overhead 10 pieces of A4 document,
so that make the new needle have a running-in process, and then put the ribbon. I hope you can be careful operation.
2.If the original print head was broken and especially leaked ink, the mainboard has burned possibly,
so please troubleshoot the problem of the mainboard before replacing the print head. In addition,
the F1,F2 fuze wire of mainboard can only be replaced by the original fuze that has same current value and same model.
If replacing fuze that is biger current value and different model, Both printhead and mainboard are possible to be broken.
3.Print head requires lots of attention, It is easy to cause man-made damage if a non-professionals replace printhead blindly.
There is a regulation that printhead is not warranty, and it is delicate and expensive.
please do not make commissioning on the machine, and please treat it with caution.
4.If you are not familiar with the machine, it is recommended that you had better send the print head to a repair station or find professionals to replace the nozzle, so as to avoid unnecessary losses and unnecessary trouble.

Free Shipping
Delivery Time: 2-6 working days

Returns: Customers have the right to apply for a return within 60 days after the receipt of the product
24-Hour Expert Online: Solve your installation and product problems

Customer Reviews

Based on 17 reviews
Easy to install

Easy to install and go online, only a few issues need attention. 1) I tried to use a set of ink cartridges from my old print head (real HP), but the ink was not enough. The print head will not complete its start-up cycle until I replace the old ink cartridge with the new ink cartridge that came with the print head. 2) Somehow, the wireless connection was lost, and I couldn't get the printer to recognize the network until the printer completed its startup cycle. Once the printer has completed its cycle, I use the power button to turn off the printer, and then unplug the power plug for a few seconds. When I plug in the power and press the on/off button to power it, the printer works normally. Very cost-effective, I will come back again when I need it next time

James Martinez
printer works again

We have an HP Officejet Pro 8620 in our office, which we use all day long. I cannot print, and there is an error message that the print head is damaged/missing. After googled the error message, I found that the print head needs to be replaced (the component where the ink cartridge is located). Found the assembly on and ordered it. I just received the package, the packaging is good, including the return label and instructions. I did it step by step following the HP instructions I found online. The printer works again and the print quality is great!

Satisfied up and printing again

I performed many cleaning and adjustment task before running across your product . While reviewing your product online I found many applicable instructions of what to expect and do to install a new print head. I purchase your product and installed it according to your instructions on line .The installation was very successful and print is performing like new . Your prcing is competitive and I am glad that I repalced the print head I love my old printer and have lots of ink so I did not want to by a new printer. Thank you!

Aaron Cooper
Solid Replacement

Easy fix to the apparently frequent issue of printer head failure on HP 8620. Not cheap, but solved the problem.

Great Results!!

It took a little while to get the new printhead to work properly. I went back and followed the instructions very closely, such as reinserting the new print head 3 times, then cleaning the new printhead 3 times to clear the manufacturing fluids, It took all 3 times to clear the head for the ink to flow properly. Then, after going through the printhead realignment function, the printhead works perfectly!! Thank you!!

But, what can I do with the old printhead to have as a backup? Probably backed-up internally with dried ink and needs internal flushing to clear the old ink. I didn't use this particular printer much at all for several years, which probably caused the printhead internal ink drying problem. Can your company refurbish my old printhead? Please advise me.

Hi, thank you for your support. If you need more help, please contact our customer service via email

Payment & Security

American Express Diners Club Discover JCB Maestro Mastercard PayPal Union Pay Venmo Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

You may also like

Recently viewed